哪个E文好帮我翻译一下?我机器出故障了..
哎..买了个PC1000E 两个月就后故障不断...就没用顺心过...老是出现Ｃ：３１：４２错误
老是提示这个错误．．．显示出盒标志 换了Ｎ种带子都不行．．．现在用的松下ＭＱ带．也是不行．．．
这种天气不可能结露的啊．．．在网上查了一下．．．也没说什么．无非就是把带子重插一次．．．．重插Ｎ次都不行．．．
是不是带仓错位了？
然后在网上查了一下．．．发现稀少．．．就看到一篇帖子．．．拿金山大概翻译了一下．．排除了几个结露导致问题的回答．．然后就剩下这一大片．．．
哪位朋友帮忙翻译一下～谢谢了．．．．
I'm copying what I've wrote there:
I had the same C:31:42 error on my DCR-TRV725E. Suddenly, out of nowhere, it started. On every cassette, sometimes with few seconds disturbed playback or few seconds of rewind/forward. I searched the Internet and found this forum. People here said that the solution was to take the camera apart and put it back together - well, it WORKED !!! I took out all the screws I could see (except the ones near the LCD). Note the two different screws near the button panel opposite the LCD screen. I pulled out the front of the camera, and then separated it into two parts in the middle all the way from the lens to the battery. In the cassette compartment "area" I only took out the plastic cover (didn't touch the screws of the mechanism inside). Be careful on the cables connecting all those parts. The camera was disconnected into 4 parts (lens, left with LCD, right with cassette compartment and battery, the 4th is this small i.Link cover on top aside). The ONLY thing I touched was this small transparent purple stick near the middle of the cassette compartment - just near the drum. I cleaned it a bit with ear cleaner. I don't know if this did the trick, but that was the only thing I can think of. Then, when the camera was all wide open, I connected the battery, inserted a cassette - and it worked. I felt like in terminator 2 when the robot comes back alive. I saw that the tape is rolling and not stopping and beeping, I could not look through the eyepiece since I had to hold all the parts in my hand, so my girlfriend looked. I put all the pieces together and it still worked. I could record and playback. All this disassembling and assembling happened 2 hours ago. God bless the Internet :)
Did you ever find an answer as to why simply taking the camera apart and putting back together again fixed it? I had the same C31:42 code on my Handycam DCR TR7000. Before I searched the web, I took the camera appart to clean everything. It already looked clean as new but I cleaned it out anyway. I then put it back together and now it works fine. Cleaning it might have fixed it but I highly doubt it. I think there is something else. My guess is that something inside the camera was sticking. Taking the camera apart was enough to break this stuck part loose. That's my best guess. DeWayne
hi. I had the same problem on my trv 340e C:31:42. I tried many things. I thought it is the condensation but after some time found out that it is the assembly. first, i tried to remove battery and isert back. then load the tape. it works. Then after some time, it just refused to do so. second. I tried to open the casing etc and fixed back. put the whole thing in a air tight container with fresh silica gell. fixed back and it's ok. third. after some time, nothing seems to work. I sent it to Sony and they changed the assembly chasis. I misplaced the resit so i cannot recall the exact part no. It has worked since. It comes with a 3 month warranty. They also replace a cable and one small part. All in comes to about RM400 which is around USD120. I was thinking to buy a new panasonic 3ccd which is very very much cheaper than the sony 3ccd. Also I heard that it is quite durable. One word of advice. When loading or removing the tape, please make sure you tae great care and caution. Do it gently and avoid putting unnecessary pressure on the casing that receives the tape. Else, your assembly will misaligned or something and it will just lead to this similar error
So make sure when inserting the tape, do it carefully. Also do close the cover slowly and press where indicated.
The chassis assembly consist on some switches activated by the moving levers. When closing or opening, the lever will open or close some switches. So that is why they say to remove tape, insert tape, remove battery, insert battery and on the cam. Hope fully when done repeatedly a couple of times, the switch surface becomes shiny again and contact is achieved to activate the switch.
I believe that my faulty assembly sacing might not be really fauly and by simple adding some solder to the mechanical contact point, the contact is good again. Wonder why dont they use gold contacts. Also I do not see any misalignment on the faulry parts so i strongly suggest the swith/soldering on the chassis is to be blamed.
Hello Everyone, I had this error occur today while trying to review Christmas footage. Here's a summary of what happened.... I had just picked up the camcorder and turned it on to record some more christmas footage of the kids. Then I got the error. c:31:42. I have an older camcorder, so I tried the tape in there and got the same code! No matter what tape I put in the first camcorder, I kept getting the error. I noticed that with my old camcorder (both Sonys) the error message came up only once more when I put in a new tape, then when I ejected the new tape and put it back in, it worked. So, I opened the tape and noticed the some of the edges were a little crimped. I don't know what that happened, but luckily it was at the end of one scene and the start of blank tape. So, I just spliced the bad tape out and it worked. I found out that 8mm tapes are not the same as vhs when you need to unlock the cassette reels to let them spin. On VHS, you could just push in, but on 8mm, you have to pull down on the little square in the back middle bottom of the tape. I hope this helps someone out there.
老是提示这个错误．．．显示出盒标志 换了Ｎ种带子都不行．．．现在用的松下ＭＱ带．也是不行．．．
这种天气不可能结露的啊．．．在网上查了一下．．．也没说什么．无非就是把带子重插一次．．．．重插Ｎ次都不行．．．
是不是带仓错位了？
然后在网上查了一下．．．发现稀少．．．就看到一篇帖子．．．拿金山大概翻译了一下．．排除了几个结露导致问题的回答．．然后就剩下这一大片．．．
哪位朋友帮忙翻译一下～谢谢了．．．． I'm copying what I've wrote there:
I had the same C:31:42 error on my DCR-TRV725E. Suddenly, out of nowhere, it started. On every cassette, sometimes with few seconds disturbed playback or few seconds of rewind/forward. I searched the Internet and found this forum. People here said that the solution was to take the camera apart and put it back together - well, it WORKED !!! I took out all the screws I could see (except the ones near the LCD). Note the two different screws near the button panel opposite the LCD screen. I pulled out the front of the camera, and then separated it into two parts in the middle all the way from the lens to the battery. In the cassette compartment "area" I only took out the plastic cover (didn't touch the screws of the mechanism inside). Be careful on the cables connecting all those parts. The camera was disconnected into 4 parts (lens, left with LCD, right with cassette compartment and battery, the 4th is this small i.Link cover on top aside). The ONLY thing I touched was this small transparent purple stick near the middle of the cassette compartment - just near the drum. I cleaned it a bit with ear cleaner. I don't know if this did the trick, but that was the only thing I can think of. Then, when the camera was all wide open, I connected the battery, inserted a cassette - and it worked. I felt like in terminator 2 when the robot comes back alive. I saw that the tape is rolling and not stopping and beeping, I could not look through the eyepiece since I had to hold all the parts in my hand, so my girlfriend looked. I put all the pieces together and it still worked. I could record and playback. All this disassembling and assembling happened 2 hours ago. God bless the Internet :)
Did you ever find an answer as to why simply taking the camera apart and putting back together again fixed it? I had the same C31:42 code on my Handycam DCR TR7000. Before I searched the web, I took the camera appart to clean everything. It already looked clean as new but I cleaned it out anyway. I then put it back together and now it works fine. Cleaning it might have fixed it but I highly doubt it. I think there is something else. My guess is that something inside the camera was sticking. Taking the camera apart was enough to break this stuck part loose. That's my best guess. DeWayne
hi. I had the same problem on my trv 340e C:31:42. I tried many things. I thought it is the condensation but after some time found out that it is the assembly. first, i tried to remove battery and isert back. then load the tape. it works. Then after some time, it just refused to do so. second. I tried to open the casing etc and fixed back. put the whole thing in a air tight container with fresh silica gell. fixed back and it's ok. third. after some time, nothing seems to work. I sent it to Sony and they changed the assembly chasis. I misplaced the resit so i cannot recall the exact part no. It has worked since. It comes with a 3 month warranty. They also replace a cable and one small part. All in comes to about RM400 which is around USD120. I was thinking to buy a new panasonic 3ccd which is very very much cheaper than the sony 3ccd. Also I heard that it is quite durable. One word of advice. When loading or removing the tape, please make sure you tae great care and caution. Do it gently and avoid putting unnecessary pressure on the casing that receives the tape. Else, your assembly will misaligned or something and it will just lead to this similar error
So make sure when inserting the tape, do it carefully. Also do close the cover slowly and press where indicated.
The chassis assembly consist on some switches activated by the moving levers. When closing or opening, the lever will open or close some switches. So that is why they say to remove tape, insert tape, remove battery, insert battery and on the cam. Hope fully when done repeatedly a couple of times, the switch surface becomes shiny again and contact is achieved to activate the switch.
I believe that my faulty assembly sacing might not be really fauly and by simple adding some solder to the mechanical contact point, the contact is good again. Wonder why dont they use gold contacts. Also I do not see any misalignment on the faulry parts so i strongly suggest the swith/soldering on the chassis is to be blamed.
Hello Everyone, I had this error occur today while trying to review Christmas footage. Here's a summary of what happened.... I had just picked up the camcorder and turned it on to record some more christmas footage of the kids. Then I got the error. c:31:42. I have an older camcorder, so I tried the tape in there and got the same code! No matter what tape I put in the first camcorder, I kept getting the error. I noticed that with my old camcorder (both Sonys) the error message came up only once more when I put in a new tape, then when I ejected the new tape and put it back in, it worked. So, I opened the tape and noticed the some of the edges were a little crimped. I don't know what that happened, but luckily it was at the end of one scene and the start of blank tape. So, I just spliced the bad tape out and it worked. I found out that 8mm tapes are not the same as vhs when you need to unlock the cassette reels to let them spin. On VHS, you could just push in, but on 8mm, you have to pull down on the little square in the back middle bottom of the tape. I hope this helps someone out there.
